Ariens 916003 - AMP 24 Especificaciones

Owner/Operator ManualManuel Du Propriétaire/UtilisateurModel916003 – AMP 2403982600C 6/10Printed in USAENGLISHFRANÇAISAMP 24

GB - 10Install Remote Deflector Cable(Figure 8 and 9)1. Slide cable through clip on top of discharge chute pedestal Figure 8.2. Bend clip closed aroun

GB - 11.Charge BatteriesThe batteries MUST be charged for a minimum of 7 hours before the first use.See Pre-Start on page 15.IMPORTANT: The unit MUST

GB - 121. Attachment Clutch Lever2. Speed Selector3. Remote Deflector Lever4. Traction Drive Clutch Lever5. Chute Crank 6. Discharge Chute Deflector7.

GB - 13CONTROLS AND FEATURESSee Figure 10 for all Controls and Features locations.Dual Handle Interlock When attachment clutch and then traction drive

GB - 14Speed SelectorPosition the Speed Selector in the appropriate speed notch to control forward and reverse travel.IMPORTANT: DO NOT change motion

GB - 15Scraper BladeThe scraper blade allows the back of the housing to keep better contact with the surface being cleared. It also prevents damage to

GB - 164. Plug battery charger into wall outlet. Do not use an extension cord unless necessary. If an extension cord is needed follow the manufacturer

GB - 172. Check Dual Handle InterlockWithout the drive motor running, press down (engage) both clutch levers. Release attachment clutch lever. Attachm

GB - 18TRANSPORTALWAYS move PTO and power switches to OFF position and remove key when transporting unit on a truck or trailer.Use extra care when loa

GB - 19CHECK CLUTCH OPERATIONAuger and impeller must stop within 5 seconds when attachment clutch/impeller brake lever is released.Wheels must stop qu

GB - 2SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . 4ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . 8CONTROLS and FEATURES . . . .

GB - 20SCRAPER BLADEIMPORTANT: Damage to auger/impeller housing will result if blade wears down too far.Scraper blade is adjustable to compensate for

GB - 21SHEAR BOLTSIMPORTANT: Use only Ariens shear bolts for replacement. Use of any other type of shear bolt may result in severe damage to unit and

GB - 22REMOVING AND INSTALLING BATTERIESRemoval1. Move power and PTO switches to the OFF position. Remove key from switch.2. Remove four screws securi

GB - 23ATTACHMENT DRIVE BELT REPLACEMENTRemove Attachment Drive Belt (Figures 24, 25 and 26)1. Move power and PTO switches to the OFF position. Remove

GB - 24Replace Attachment Drive Belt1. Place new belt onto attachment pulley.NOTE: Hold down the attachment clutch lever to make it easier to reconnec

GB - 255. Pull idler away from traction drive belt and remove belt from idler, drive pulley and driven pulley.6. Replace traction drive belt.7. Swing

GB - 26Check Attachment Idler Arm Roller Clearance1. Place the unit into the service position (see Service Position on page 18). Remove the bottom cov

GB - 272. Adjust cable length (See Figure 32).a. Loosen jam nut on cable.b. To increase spring extension, adjust barrel down the cable and tighten jam

GB - 28FRICTION DISC REPLACEMENTRemove Friction DiscFigure 361. Move PTO and power switches to OFF position. Remove key.2. Disconnect and remove batte

GB - 2918. Connect pivot pin to speed selector arm. See Speed Selector Adjustment on page 22.19. Install bottom cover.20. Install wheels.21. Return un

GB - 3PRODUCT REGISTRATIONThe Ariens dealer must register the product at the time of purchase. Registering the product will help the company process w

GB - 30Unit throws snow poorly or does not throw snow. 1. Shear bolts broken. 1. Replace shear bolts (see Shear Bolts on page 21). 2. Attachment clut

GB - 31BATTERY CHARGING TROUBLESHOOTINGPROBLEM PROBABLE CAUSE CORRECTIONBattery charger LED indicators do not light. 1. No power to battery charger. 1

GB - 32SPECIFICATIONSModel Number 916003Description AMP 24MotorType Electric Brushless DCElectricalBattery 48 Volt Maintenance Free VRLAPTO (Power Tak

ARIENS COMPANYGRAVELY® | STENS® | LOCKE® | NATIONAL® | BYNORM® | EVERRIDE® | GREAT DANE® Snow_201033Three-Year Limited Sno-Thro® WarrantyAriens Compa

ARIENS COMPANYGRAVELY® | STENS® | LOCKE® | NATIONAL® | BYNORM® | EVERRIDE® | GREAT DANE® Snow_201034 Exclusions – Items Not Covered by This Warranty•

Ariens Company655 West Ryan StreetBrillion, WI 54110-1072920-756-2141Fax 920-756-2407www.ariens.comwww.ampbyariens.com

GB - 4SAFETY ALERTSLook for these symbols to point out important safety precautions. They mean:Attention! Personal Safety Is Involved!Become Alert!

GB - 52. DANGER! 3. DANGER!SAFETY RULESRead, understand, and follow all safety practices in Owner/Operator Manual before beginning assembly or operati

GB - 6DO NOT operate near drop-offs, ditches, or embankments. Unit can suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an ed

GB - 7DO NOT operate on steep slopes. DO NOT clear snow across the face of slopes. Keep all movement on slopes slow and gradual. DO NOT make sudden ch

GB - 8PACKAGE CONTENTSASSEMBLYTools Required:• Pliers• Hex Key (Included)• Open-End Wrenches: 3/8, 7/16, 1/2, 9/16 in. and/or Adjustable Wrench•Tire G

GB - 9Install Discharge ChuteFigure 51. Grease underside of discharge chute ring (if not already greased).2. Remove mounting hardware from the bottom